- •Isbn: 3-527-30999-3
- •Introduction
- •Isbn: 3-527-30999-3
- •1072 1 Introduction
- •Isbn: 3-527-30999-3
- •Inventor of stone groundwood. Right: the second version
- •1074 2 A Short History of Mechanical Pulping
- •In refining, the thinnings (diameter 7–10cm) can also be processed.
- •In mechanical pulping as it causes foam; the situation is especially
- •In mechanical pulping, those fibers that are responsible for strength properties
- •Isbn: 3-527-30999-3
- •In mechanical pulping, the wood should have a high moisture content, and the
- •In the paper and reduced paper quality. The higher the quality of the paper, the
- •1076 3 Raw Materials for Mechanical Pulp
- •1, Transversal resistance; 2, Longitudinal resistance; 3, Tanning limit.
- •3.2 Processing of Wood 1077
- •In the industrial situation in order to avoid problems of pollution and also
- •1078 3 Raw Materials for Mechanical Pulp
- •2, Grinder pit; 3, weir; 4, shower water pipe;
- •5, Wood magazine; 6, finger plate; 7, pulp stone
- •Isbn: 3-527-30999-3
- •4.1.2.1 Softening of the Fibers
- •1080 4 Mechanical Pulping Processes
- •235 °C, whereas according to Styan and Bramshall [4] the softening temperatures
- •Isolated lignin, the softening takes place at 80–90 °c, and additional water
- •4.1 Grinding Processes 1081
- •1082 4 Mechanical Pulping Processes
- •1, Cool wood; 2, strongly heated wood layer; 3, actual grinding
- •4.1.2.2 Defibration (Deliberation) of Single Fibers from the Fiber Compound
- •4 Mechanical Pulping Processes
- •Influence of Parameters on the Properties of Groundwood
- •In the mechanical defibration of wood by grinding, several process parameters
- •Improved by increasing both parameters – grinding pressure and pulp stone
- •In practice, the temperature of the pit pulp is used to control the grinding process,
- •In Fig. 4.8, while the grit material of the pulp stone estimates the microstructure
- •4 Mechanical Pulping Processes
- •4.1 Grinding Processes
- •Is of major importance for process control in grinding.
- •4 Mechanical Pulping Processes
- •4.1.4.2 Chain Grinders
- •Is fed continuously, as shown in Fig. 4.17.
- •Initial thickness of the
- •4 Mechanical Pulping Processes
- •Include:
- •Increases; from the vapor–pressure relationship, the boiling temperature is seen
- •4 Mechanical Pulping Processes
- •In the pgw proves, and to prevent the colder seal waters from bleeding onto the
- •4.1 Grinding Processes
- •In pressure grinding, the grinder shower water temperature and flow are
- •70 °C, a hot loop is no longer used, and the grinding process is
- •4 Mechanical Pulping Processes
- •Very briefly at a high temperature and then refined at high
- •4.2 Refiner Processes
- •4 Mechanical Pulping Processes
- •Intensity caused by plate design and rotational speed.
- •4.2 Refiner Processes
- •1. Reduction of the chips sizes to units of matches.
- •2. Reduction of those “matches” to fibers.
- •3. Fibrillation of the deliberated fibers and fiber bundles.
- •1970S as result of the improved tmp technology. Because the key subprocess in
- •4 Mechanical Pulping Processes
- •Impregnation Preheating Cooking Yield
- •30%. Because of their anatomic structure, hardwoods are able to absorb more
- •Is at least 2 mWh t–1 o.D. Pulp for strongly fibrillated tmp and ctmp pulps from
- •4 Mechanical Pulping Processes
- •4.2 Refiner Processes
- •1500 R.P.M. (50 Hz) or 1800 r.P.M. (60 Hz); designed pressure 1.4 mPa
- •1500 R.P.M. (50 Hz) or 1800 r.P.M. (60 Hz); designed pressure 1.4 mPa;
- •4.2 Refiner Processes
- •4 Mechanical Pulping Processes
- •In hardwoods makes them more favorable than softwoods for this purpose. A
- •4.2 Refiner Processes
- •Isbn: 3-527-30999-3
- •1114 5 Processing of Mechanical Pulp and Reject Handling: Screening and Cleaning
- •5.2Machines and Aggregates for Screening and Cleaning 1115
- •In refiner mechanical pulping, there is virtually no such coarse material in the
- •1116 5 Processing of Mechanical Pulp and Reject Handling: Screening and Cleaning
- •5.2Machines and Aggregates for Screening and Cleaning
- •5 Processing of Mechanical Pulp and Reject Handling: Screening and Cleaning
- •5 Processing of Mechanical Pulp and Reject Handling: Screening and Cleaning
- •5.3 Reject Treatment and Heat Recovery
- •55% Iso and 65% iso. The intensity of the bark removal, the wood species,
- •Isbn: 3-527-30999-3
- •1124 6 Bleaching of Mechanical Pulp
- •Initially, the zinc hydroxide is filtered off and reprocessed to zinc dust. Then,
- •2000 Kg of technical-grade product is common. Typically, a small amount of a chelant
- •6.1 Bleaching with Dithionite 1125
- •Vary, but are normally ca. 10 kg t–1 or 1% on fiber. As the number of available
- •1126 6 Bleaching of Mechanical Pulp
- •6.2 Bleaching with Hydrogen Peroxide
- •70 °C, 2 h, amount of NaOh adjusted.
- •6.2 Bleaching with Hydrogen Peroxide
- •Is shown in Fig. 6.5, where silicate addition leads to a higher brightness and a
- •Volume (bulk). For most paper-grade applications, fiber volume should be low in
- •Valid and stiff fibers with a high volume are an advantage; however, this requires
- •1130 6 Bleaching of Mechanical Pulp
- •6.2 Bleaching with Hydrogen Peroxide
- •Very high brightness can be achieved with two-stage peroxide bleaching, although
- •In a first step. This excess must be activated with an addition of caustic soda. The
- •Volume of liquid to be recycled depends on the dilution and dewatering conditions
- •6 Bleaching of Mechanical Pulp
- •6 Bleaching of Mechanical Pulp
- •Is an essential requirement for bleaching effectiveness. Modern twin-wire presses
- •Is discharged to the effluent treatment plant. After the main bleaching stage, the
- •6.3 Technology of Mechanical Pulp Bleaching
- •1136 6 Bleaching of Mechanical Pulp
- •Isbn: 3-527-30999-3
- •7.3 Shows the fractional composition according to the McNett principle versus
- •1138 7 Latency and Properties of Mechanical Pulp
- •7.2 Properties of Mechanical Pulp 1139
55% Iso and 65% iso. The intensity of the bark removal, the wood species,
and the storage time between wood harvest and refining has a huge impact
on the unbleached brightness level. The use of sawmill waste normally provides a
lower unbleached brightness. Generally the use of a mechanical pulp in higher
quality paper grades such as SC or LWC paper requires a bleaching step.
Lignin is the dominant source of chromophores in mechanical pulp, with aromatic
ring structures with conjugated side chains, quinones, quinone methids
and metal–catechol complexes being the origin of the color. Chemically, decolorization
or destruction of these compounds is accomplished by either reductive or
oxidative processes.
An example of the brightness gains achieved in bleaching with dithionite or
hydrogen peroxide is shown in Fig. 6.1. Based on the initial brightness levels, the
range between 70% ISO to about 80% ISO is accessible for softwood. Hardwood
pulps can be bleached to >85% ISO. The top brightness requires more than one
bleaching stage. The higher the brightness target, the more complicated the
bleaching technology becomes. The simplest way to improve brightness is to treat
Handbook of Pulp. Edited by Herbert Sixta
Copyright © 2006 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim
Isbn: 3-527-30999-3
©2006 WILEY-VCHVerlag GmbH&Co .
Handbook of Pulp
Edited by Herbert Sixta
0 1 2 3 4 5
0
5
10
15
20
Dithionite Peroxide
Brightness gain [% ISO points]
Chemical charge [%]
Fig. 6.1 Typical response of mechanical pulp to oxidative or reductive
bleaching with hydrogen peroxide or dithionite (hydrosulfite).
the pulp with sulfur dioxide. The reduction of transition metals decolorizes the
above-mentioned catechol–metal complexes. Metal ions reduction not only decolorizes
the chromophores but also solubilizes the metals and allows their removal
by washing and subsequent dewatering. Because the reduction is easily reverted
by air oxidation, all reductive bleaching treatments require “closed” systems.
Because air can be excluded from pulp slurries more easily at a lower consistency,
reductive bleaching in the past was conducted in up-flow towers at only 3–5% consistency.
The de-aeration which takes place in modern medium-consistency
pumps permits reductive bleaching at consistencies from 8% to 14% (see Section
II-6.3). This allows a smaller size of reactors to be used (tubes instead of towers)
and a lower volume of process water.
6.1
Bleaching with Dithionite
The impact of the reduction process is intensified with the application of dithionite,
which in addition reduces quinones and quinone methids. (In Englishspeaking
countries, dithionite is frequently still labeled as “hydrosulfite”, an incorrect
description of the product, but this was rectified in 1881.) The dominant compound
used in bleaching processes is sodium dithionite, and in the description of
bleaching processes the normal abbreviation for dithionite bleaching is “Y”.
Sodium dithionite is produced using several processes, but historically the zinc
dust process is the most important. The reaction of zinc dust in an aqueous slurry